Pitch bend: modifies any currently playing note. Adjustable range from 0 to 5 octaves.
Sustain: holds a note on while the sustain is active.
Aftertouch: selectable as an aux and/or control output.
Expression: selectable as an aux and/or control output.
Mod wheel: selectable as an aux and/or control output.
Effect 1: selectable as an aux and/or control output.
Effect 2: selectable as an aux and/or control output.
Start and Continue sequence: selectable as an aux and/or control output.
Stop sequence: selectable as an aux and/or control output.
Mute (all notes off): clears any note, velocity, and gate outputs.
Clock tick: MIDI clock ticks are sent directly to the Clock output and can be routed as an aux and/or control output.
Reset: reset the MIDI input messaging queue and stops any output.
Inputs
MIDI in: single channel or respond to all channels (omni)
Both MIDI via UART and class-compliant USB MIDI
Menu navigation: Rotary encoder with push switch
Outputs
Four CV outputs:
Note: 0 to 10v output (selectable to 0 to 5v) for CV with 1v per octave.
Velocity: 0 to 10v output (selectable to 0 to 5v) for velocity / volume
Out 1: customizable CV output (0v to +10v max, selectable to 0v to +5v)
Out 2: customizable CV output (0v to +10v max, selectable to 0v to +5v)
Trigger: single pulse when a note turns on, with customizable pulse on time (high / low level output)
Gate: signal goes high while a note is on (high / low level output)
Clock: 1ms pulse with each MIDI clock tick (high / low level output). Selectable to various clock divisions.
Using the MCM-100-EX Expansion Module, you can also add an additional four assignable CV outputs.
Power
This module requires a 10 pin (2x05 IDC connector) Eurorack power connection.
Be certain when you plug the connector in that the orientation is the correct way, with the -12v line (usually with the red stripe) on the left when looking at the rear of the module.
Usage
On startup, you should see the boot screen with the current version:
The note and clock LEDs should turn on and off a few times before the dashboard screen is shown and the module is ready to be used.
The dashboard shows the status of the current MIDI channel that it is listening on, as well as various outputs:
The note and octave
vel: The current velocity (corresponding to 0v to +10/+5v)
o1: The current Out 1 value (corresponding to 0v to +10/+5v)
o2: The current Out 2 value (corresponding to 0v to +10/+5v)
Indicators for the state of the trigger, gate, and clock
If the MCM-100-EX expansion module is attached, additionally it will show:
x1: The current Out X1 value (corresponding to 0v to +10/+5v)
x2: The current Out X2 value (corresponding to 0v to +10/+5v)
x3: The current Out X3 value (corresponding to 0v to +10/+5v)
x4: The current Out X4 value (corresponding to 0v to +10/+5v)
While using the module, you can turn the dashboard display on and off via the display settings menu.
You can also adjust how often the display refreshes (set to a longer time if display events start to get dropped, shorter time for more frequent updates).
Settings Menu
There are numerous settings available from the settings menu.
Pressing the encoder button on the dashboard display (regardless if the display is visible or not) will enter the menu.
See the Menu System documentation for the menu system details.
Note: any settings are not persisted until you exit the menu back to the dashboard (with the exception of when resetting the settings to default).
PICO_SDK_PATH {the path to the PICO_SDK directory)
PICO_TOOLCHAIN_PATH (path to the pico toolchain for your build machine)
# You should _not_ have to change the following
set(PICO_PLATFORM rp2040)
set(PICO_BOARD pico)
Build script
./build.sh
This will run the full clean and build.
The firmware file will be put in:
./dist/TechWaveAudio-MCM-v2.0.0.uf2
Firmware Updates
For this, you'll need a firmware release (or build your on locally), as well as a USB cable that has a micro-usb port on one end.
Power off your rack.
Remove the module from your rack but keep the module plugged in via the power cable.
Download the desired firmware file version from the GitHub repository firmware release. You only need to download the file with the .uf2 extension.
Plug your USB-C cable into the jack on the front of the module and the other end into the computer with the firmware.
While holding down the small boot select (BOOTSEL) button on the board, power on the module. Keep holding the boot select button until the module appears on your computer. The on-board Raspberry Pi Pico board will appear as a mass storage device, usually named “RPI-RP2”
Copy the downloaded firmware .uf2 file to the storage device. When complete, the module should reboot.
Power off your rack again.
Disconnect your USB cable from the module and your computer. Your computer may give you a warning about the device not being properly ejected. You can safely ignore this warning.
Put the module back into your rack and power back on.
Note that any settings you many have modified will be reset to any default.
Design
Schematic, PCB, and hardware
See the hardware design documentation for information on the schematic and PCB design for the module.
Note - all files provided including KiCad designs and any gerber files are provided as-is and to be used at your own risk.
TechWave Audio does not guarantee the accuracy or any correctness of these files.
See the HW_LICENSE license file for more, specifically the section "6 DISCLAIMER AND LIABILITY".
Licensing
Software in this repository is licensed under the BSD-3 License. By using or contributing content to this repository you are agreeing to place your contributions under this license.
No comments yet. Be the first to ask about this board.