Loading 3D model… large boards can take a moment.
A passive continuity tester for USB cables, designed in KiCad 10.
Plug one end of a cable into a source connector and the other end into a sink connector. Each conductor present in the cable lights its own LED, so you can see at a glance whether a cable is charge-only, USB 2.0, or fully wired for USB 3.x, and spot broken or missing wires.
[!WARNING] Never plug the checker into a real device, host or charger. Every contact on the source side, including GND and shield, sits at the test voltage.
VTEST.The full schematic is in docs/usb-cable-checker-schematic.pdf.
The sink connectors are labelled a–f on the silkscreen.
| Side | Ref | Board label | Connector |
|---|---|---|---|
| Source | J1 | TypeC 3.0 | USB-C (full 24-pin, USB 3.x) |
| Source | J2 | TypeA 2.0 | USB-A 2.0 |
| Source | J3 | TypeA 3.0 | USB-A 3.0 |
| Sink | J5 | a | USB-B 3.0 |
| Sink | J4 | b | USB-C (full 24-pin, USB 3.x) |
| Sink | J6 | c | Micro-B 3.0 |
| Sink | J7 | d | Mini-B |
| Sink | J8 | e | Lightning |
| Sink | J9 | f | Micro-B 2.0 |
The 26 LEDs follow the USB-C pin numbering and are labelled on the board in two rows, PINROW A and PINROW B.
| LEDs | Contacts |
|---|---|
| D101–D112 | A1–A12: GND, TX1+, TX1−, VBUS, CC1, D+, D−, SBU1, VBUS, RX2−, RX2+, GND |
| D201–D212 | B1–B12: GND, TX2+, TX2−, VBUS, CC2, D+, D−, SBU2, VBUS, RX1−, RX1+, GND |
| D113 | ID (Mini-B / Micro-B) |
| D114 | Shield |
What to expect from a good cable:
| Cable | LEDs that light |
|---|---|
| Charge-only | VBUS and GND only |
| USB 2.0 (any connector type) | VBUS, GND, D+ and D− |
| USB 3.x (USB-A 3.0 to USB-B 3.0, Micro-B 3.0 or USB-C) | The USB 2.0 set, plus the TX and RX pairs |
| Full-featured USB-C to USB-C | VBUS, GND, D+/D−, one CC line, all four TX/RX pairs, SBU1 and SBU2 |
Each row also has a round probe pad next to its label (TD1–TD26), so you can measure a conductor with a multimeter.
SW1 selects the supply for VTEST:
The solder jumpers are open by default.
| Ref | Function |
|---|---|
| JP1 | Bridge to tie sink CC1 to GND |
| JP2 | Bridge to tie sink CC2 to GND |
| JP3 | Bridge to tie sink shield to GND |
| TP1 / TP2 | Battery + / − pads beside the CR2032 holder |
| Top | Bottom |
|---|---|
production/bom.csv.| Path | Contents |
|---|---|
usb-cable-checker.kicad_pro | KiCad project (open this) |
usb-cable-checker.kicad_sch | Schematic |
usb-cable-checker.kicad_pcb | PCB layout |
usb-cable-checker.kicad_dru | Custom design rules |
fp-lib-table, sym-lib-table | Project library tables (point into lib/) |
lib/usb_checker.kicad_sym | Symbols for the connectors, battery holder and switch |
lib/usb_checker.pretty/ | Footprints for the connectors, battery holder, switch, test pads and LEDs |
lib/usb_checker.3dshapes/ | 3D models for the connectors, battery holder and switch |
production/gerbers/ | Gerber and drill files |
production/bom.csv | Bill of materials (JLCPCB format, with LCSC part numbers) |
production/cpl.csv | Component placement (pick-and-place) file |
docs/ | Schematic PDF and board renders |
The resistors, capacitors, LEDs, diode and regulator use KiCad's standard
libraries (Device, Diode, Regulator_Linear, Resistor_SMD,
Capacitor_SMD, LED_SMD, Diode_SMD, Package_TO_SOT_SMD), as do the
power, Connector, Jumper and MountingHole parts. Everything else is in
lib/, so the project opens on any standard KiCad 10 install.
production/gerbers/ and upload the zip to your PCB fab.production/bom.csv and
production/cpl.csv.If you regenerate the placement file from KiCad, check the LED (D101–D212) and
regulator (U1) rotations in the fab's preview. The KiCad standard footprints for
these are rotated 180° from EasyEDA's, and the supplied cpl.csv already
accounts for that.
Copyright 2026 USB Cable Checker contributors.
This source describes Open Hardware and is licensed under the CERN-OHL-P v2.
You may redistribute and modify this source and make products using it under
the terms of the CERN-OHL-P v2 (https://ohwr.org/cern_ohl_p_v2.txt). This
source is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF
MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE.
Please see the CERN-OHL-P v2 for applicable conditions. See LICENSE.
The CERN-OHL-P covers the design. Some library parts in lib/ were not created
for this project and keep their own terms:
LED_0603_1608Metric_NoSilk is KiCad's LED_SMD:LED_0603_1608Metric with
its silkscreen removed. It is licensed under
CC-BY-SA 4.0 with the KiCad library exception.The two test-pad footprints (TestPad_Round_1.2mm, TestPad_Oval_3.0x5.0mm)
were made for this project and are covered by the CERN-OHL-P.
No comments yet. Be the first to ask about this board.