Loading 3D model… large boards can take a moment.
Raspberry Pi-based CD changer emulator for vintage Kenwood car stereos
Reverse-engineering the proprietary serial protocol used by 1990s Kenwood head units to communicate with their CD changers, and building an open-source emulator that replaces the changer with a Raspberry Pi — enabling unlimited music playback through the original stereo using its factory controls. Close-up front view of KRC-3006 cassette receiver
🔬 Phase: Protocol Reverse Engineering — Capturing and decoding the synchronous serial protocol between a Kenwood KRC-3006 cassette receiver and a KDC-C717 10-disc CD changer.
Phase 1 of TP-KRC3006-01 — power-on characterization — is complete. Executed 2026-04-19 on the KRC-3006 with a KDC-C717 changer connected through the pass-through breakout board. Every recorded step passed; results are published in TL-KRC3006-01-P1-20260419.
Findings that matter for the emulator design:
Testing runs inline through the DN-KRC3006-04 pass-through breakout board, serial number 1, assembled and verified per TP-KRC3006-02: Close-up view of assembled pass-through breakout board
The KDC-CX85 originally used as the reference changer was diagnosed with a dead or degraded laser diode and retired. All further testing uses the KDC-C717: Close-up front view of KDC-C717 CD auto changer
For reference, the 13-pin mini DIN changer connector pinout: Kenwood 13-pin mini DIN CD changer connector pinout and signal names
This project emulates a Kenwood CD changer on the 13-pin round DIN connector used by mid-1990s Kenwood head units. The emulator responds to all head unit commands (play, stop, next/previous track, disc selection, repeat, shuffle) and streams audio from a Raspberry Pi through the stereo's built-in amplifier.
| Component | Role |
|---|---|
| Kenwood KRC-3006 (or similar mid-90s Kenwood head unit) | The stereo — device under test |
| Kenwood KDC-C717 | CD auto changer — reference changer for protocol capture |
| Raspberry Pi 5 | Media server, web interface, audio playback |
| ATtiny1616 | Real-time Kenwood protocol handler (on custom HAT), run at 3.3V to match Pi GPIO natively |
| SN74LVC8T245PWR ×2 | 3.3V ↔ 5V bus level shifting, one per direction |
| PCM5102A I2S DAC | Digital-to-analog audio conversion |
| 1 TB NVMe SSD | Music storage (avoids SD card corruption) |
| SparkFun TOL-18627 USB Logic Analyzer | Protocol capture and analysis |
| Custom staged power adapter | Two toggle switches simulating constant and ignition power independently on the bench |
Any vintage automobile still using a Kenwood head unit with CD changer control. I am building this and testing around a KRC-3006 head unit due to it being the only shaft style cassette deck with a CD changer control port. My vehicle for this project is a 1985 Chevrolet C10 Silverado. The power supply design accounts for the electrically noisy environment of older vehicles without modern filtering.
cd_changer_emulator/
├── assets/ # Project assets. Photos and screenshots.
├── docs/ # Project documentation
│ ├── TP-KRC3006-01.odt # Test plan 1: Protocol capture test procedure (IEEE 829)
│ ├── TL-KRC3006-01.ods # Test log 1: Companion log workbook to TP-KRC3006-01
│ ├── TP-KRC3006-02.odt # Test plan 2: Breakout board test plan
│ ├── TL-KRC3006-02.odt # Test log 2: Breakout board test log
│ ├── TP-KRC3006-03.odt # Test plan 3: Emulator test procedure (IEEE 829)
│ ├── TL-KRC3006-03.ods # Test log 3: Companion log workbook to TP-KRC3006-03
│ ├── DN-KRC3006-01.md # Design note 1: HAT design research
│ ├── DN-KRC3006-02.md # Design note 2: Schematic analysis
│ ├── DN-KRC3006-03.md # Design note 3: Bluetooth stretch goal
│ ├── DN-KRC3006-04.md # Design note 4: Breakout board design
│ ├── DN-KRC3006-05.md # Design note 5: Web application design for library management
│ ├── DN-KRC3006-06.md # Design note 6: Kenwood CD changer error codes
│ ├── protocol/ # Decoded protocol data
│ └── records/ # Completed, filled-out test logs (published as PDF)
├── firmware/ # ATtiny1616 firmware (Arduino/megaTinyCore)
│ └── src/
├── software/ # Raspberry Pi software
│ ├── flask-app/ # Web interface — legacy name; being superseded by FastAPI
│ ├── mpd-config/ # Legacy name; playback is moving to python-mpv
│ ├── power-mgmt/ # ATtiny UART bridge and power state management
│ └── wifi-manager/ # AP/client mode switching
├── hardware/ # KiCad PCB design files
│ ├── kicad/
│ │ ├── changer cable breakout/ # Pass-through breakout board (complete, fabbed)
│ │ ├── emulator hat/ # Raspberry Pi HAT (schematic in progress)
│ │ └── lib/ # Shared custom symbols and footprints
│ ├── gerbers/ # Manufacturing files
│ └── bom/ # Bill of materials with JLCPCB part numbers
├── captures/ # Logic analyzer captures (.sr files)
├── diagrams/ # WaveDrom timing, Mermaid state machines, draw.io blocks
└── reference/ # Datasheets, protocol documentation, forum archives
This project targets the "O protocol" (Old protocol) used by Kenwood head units with the round 13-pin DIN CD changer connector, roughly 1990–1998. Known compatible head units include models in the KRC series (cassette receivers) and some KDC series (CD receivers) from that era [citation needed].
Later Kenwood units with a rectangular changer connector use the "C protocol" (New protocol), which has different command encoding. This project does not currently target the C protocol, but the hardware and architecture could be adapted [citation needed].
The project follows a documentation-first approach using IEEE 829-inspired test procedures. All documentation lives in the docs/ directory. Markdown is preferred wherever it fits, so design notes are written in Markdown and render directly on GitHub. The test plans and companion logs are currently kept in Open Document Format because they are table- and form-heavy, but no particular document format is required.
Test plans and test logs are created and maintained as matched pairs sharing a sequence number — TP-KRC3006-01 defines what gets tested and how, and TL-KRC3006-01 is where results are recorded. Filled-out copies of a log are published as PDF in docs/records/ as each phase completes.
| Document Name | Type | Description |
|---|---|---|
| TP-KRC3006-01 | Test Plan | Initial test plan for capturing messages between CD changer and head unit |
| TL-KRC3006-01 | Test Log | Companion log workbook to TP-KRC3006-01 |
| TP-KRC3006-02 | Test Plan | Breakout board test plan |
| TL-KRC3006-02 | Test Log | Breakout board test log |
| TP-KRC3006-03 | Test Plan | Test plan for creating and testing protocol emulation through full audio integration |
| TL-KRC3006-03 | Test Log | Companion log workbook to TP-KRC3006-03 |
| DN-KRC3006-01 | Design Note | HAT design research — ATtiny1616 selection, PCM5102A DAC circuit, automotive power supply with supercap, WiFi architecture, JLCPCB assembly |
| DN-KRC3006-02 | Design Note | Schematic analysis — KRC-3006 head unit and KDC-CX85 changer signal routing, series resistor values, protocol variant identification |
| DN-KRC3006-03 | Design Note | Bluetooth stretch goal — wireless audio streaming while retaining factory head unit controls |
| DN-KRC3006-04 | Design Note | Breakout board design — pass-through 13-pin mini DIN breakout with logic analyzer headers |
| DN-KRC3006-05 | Design Note | Web Application Design for Emulator Library Management |
| DN-KRC3006-06 | Design Note | Kenwood CD Changer Error Codes |
Per-document revision status is tracked in the documentation index.
| Record | Covers | Date |
|---|---|---|
| TL-KRC3006-01-P1-20260419 | TP-KRC3006-01 Phase 1 — power-on characterization | 2026-04-19 |
| TL-KRC3006-02-01-20260410 | TP-KRC3006-02 — breakout board serial number 1 | 2026-04-10 |
This project is in early development. If you have a compatible Kenwood head unit and want to help with protocol capture, testing, or firmware development, contributions are welcome.
.odt / .ods)This project is licensed under the MIT License — you're free to use, modify, and distribute this project for any purpose, including commercial use.
No comments yet. Be the first to ask about this board.