Loading 3D model… large boards can take a moment.
Analog synth is coming back into hype among music artists. It has a strong culture of vintage, DIY, and customisation.
On the other hand, pro systems use digical control systems, such as DMX for lighting, or OpenSoundControl (OSC) for sound.
The idea for this project is to have a hardware to interface analog synth to advanced sound control systems.
This project is also designed to leverage the possibilities of open-source show control software Chataigne.
There are a lot of solution to control an analog modular synthesizer from a computer, mainly by MIDI interfaces. But not so much options to do the opposite: control others FROM analog modulations. The features and purpose are very close to existing Befaco VCMC, but with TCP-IP for OSC instead of serial for MIDI - so we need to change the microcontroller.
Some inspiration for hardware can be found at open hardware synths from Mutable Instruments company. In its repository we can find the exact reference design, typically for the Yarns V3 MIDI digital interface.
Communication protocol dedicated to music, used for communication between musical instruments and multimedia devices. Usually it is implemented as a serial connection, with a 5-pins DIN connector.
Open, message-based protocol for communication between multimedia devices. Intended to be a next-generation replacement for MIDI. OSC specification 1.0 (Stanford University) It is usually implemented on TCP-IP stack, most usually as UDP datagrams for real time applications. It can be easily transmit thru Ethernet or Wifi at higher bit rate, and a much higher resolution of 32 bits float, than MIDI wich was based on 7 bits integer.
The analog signals generated by the synthetisers are called CV.
Other types of signals generated can be:
Chataigne is a user-friendly open-source show control software, allowing to connect several multimedia devices, hardware or software between them. We develop belongside this hardware project asynth2osc a custom module for Chataigne, so this piece of software can be use easily to control anything from a real world analog modular, from sound to light, videos and activators of any kind.
Chataigne source code on Github Artist-friendly Modular Machine for Art and Technology - Chataigne Official website
Synthetizer that uses analog circuits and signals to generate sound electronically. See the wikipedia page
Modular synthesizers are composed of separate hardware modules for different functions. The modules can be connected together by the user to create a patch. The outputs from the modules may include audio signals, analog control voltages, or digital signals for logic or timing conditions. See the wikipedia page
Open-source software that emulate analog modular synthetizers. Most of hardware modules are present. Especially, Tramasoft edited a module that is a kind of emulation of our asynth2osc module : cvOSCcv. This virtual module can be use to use real world analog hardware to control the software. VCV Rack cvOSCcv module page
Standardized mechanical format for synthetizer, in a modular 3U rack. It usually fits in a "case" to ease musicians to build their own synthetizer, and have a unique Power Supply Unit and power busses for all the modules.
The dimensions are normalised :
Exemple: Yarns is 12 HP and 3U, so front plate is 128.5x60.96mm. Its bottom PCB is tinier: 59x106,8mm, and has 3 screw holes to fit it to the front plate.
It uses 3.5mm jack for cabling, +/- 12V power supply on a 2x5p header connector, on the right lower corner of the board (facing the bottom). Red side = -12V. Print a | on the board to indicate side. Don’t forget the protection circuit.
Teensy 32 controller
8 CV muxed on 1 ADC
The first prototype includes:
The BOM is:
This RPI hat is the GPIO interface, with a very good analog front end:
Specs here
SoC: Microchip PIC16F1517-I/PT
16x 10-bit ADC
Analog input via TI SN74LV4051A 8:1 analog multiplexer
Open Collector outputs via TI DS2003CM high-current Darlington driver and NXP 74HC 8-bit parallel-in/serial out shift register.
This aims to integrate LEDs, buttons, and DACs on the same board to improve manufacturing and ralaibilty. The Raspberry Pi is dropped and replaced by a custom board with WiFi/TCP-IP SoC and all the analog stuff.
It is possible to use a PCB board as front panel too, as a lot of synthesizer modules do.
For the software part, the board would only output the OSC. I would consider implementing TinyOSC, a lightweight OSC implementation, preferably on Zephyr RTOS.
MIDI in uses an UART port, see the Arduino tutorial, or Yarns hardware. Midi-jack pinout:
UART baud rate is 31250 kbps.
This is typa A MIDI on TRS, as explain in MIDI Standard : https://midi.org/specification-for-use-of-trs-connectors-with-midi-devices Warning : There is a type B standard also in use, see https://minimidi.world/
Eurorack standard includes a +12/-12V power supply, but the currents are quite low, and sensitive to pollution. So we should rather use a 5V additional external power supply as an option.
It has to fit in Eurorack format. The smaller, the better,but no hard requirement for width. Some work has to be done to fit the connectors, leds, buttons and mechanical parts nicely.
VC analog inputs can wiggle between several voltage ranges:
We need an input stage able to fit those input the 0 / 3.3V ADC microcontroller input.
Attenuators are specific modules used to reshape a specific CV.
The most used input is copied from Mutable Instruments and remaps a -5V / 5V input in a 0 / 3.3V output, but needs a -10V bias to handle those negatives. In Befaco VCMC, an optional voltage gizmo converts 5V power supply to -12V / +12V for standalone behaviour. We could also use an inverting circuit but it will... invert: -5V mapped to 3.3V and 5V mapped to 0V.
Voltages are clamped to 0-3.3V using Shottky diodes, but it should maybe signal saturation to the user somehow.
Better scaling:
STM32H7 absolute maximum current through VDD/VSS: 620mA
STM32H7 running at 100deg, VOS1, all peripheral enabled: around 500mA
ETH PHY, 10BASE-T traffic: 130mA
OLED display logic: 300uA
3V3 LDO: 800 mA
Fuse: 1.25A, trip 2.5A
Filter ferrite rating: 3A
Schottky rating (SS24): 2A
Some modification are required from Kicad output files (BOM csv and placement files) to be imported to JLCPCB for assembly.
There is a way to automate both with a Python script called jlc-kicad-tools.
This script uses a rotation look-up-table called cpl_rotations_db.csv. Update this file with the one in this repository.
cp [PRJ]/kicad/tools/cpl_rotations_db.csv [INSTALLFOLDER]/JLCKicadTools/jlc_kicad_tools
Then install your version from the local folder:
pip3 install [INSTALLFOLDER]/JLCKicadTools
You will need 2 files in the project folder:
In order to get the project.xml file, in Eeschema, go to "Legacy BOM", create a custom XML exporter with the following command:
/bin/echo "%I"
Don’t forget to create a "JLCPCB" column with the JLCPCB references, for advanced components. For standard ones, keep their value and package and use the "--include-all-component-groups", otherwise the script will erase them.
Exemple use:
jlc-kicad-tools myproject -o ./assembly --include-all-component-groups
Here is an approximate price breakdown for manufacturing at JLCPCB. Some components, such as though-hole or big components, will be ordered separately on LCSC and soldered by hand. The "component" line includes both PCBa and by-hand BOMs. Here, we manufacture 5 boards.
| Item | Price |
|---|---|
| Components | 151€ |
| PCB manufacturing | 28€ |
| PCB assembly | 105€ |
| Shipping | 35€ |
| Refunds | 18€ |
| Total (x5 boards) | 300€ |
This is a total of 60€ / board.
First CNC run:
Reverse-mount LED options:
No comments yet. Be the first to ask about this board.