Loading 3D model… large boards can take a moment.
Pronounced "butter-fold"
A foldable, portable sibling of the btrfly keyboard https://github.com/SolidHal/btrfly-keyboard
and a variant, the btrfld ulp (ultra low profile)
More images available in "FinishedPictures" folder the btrfld folding and unfolding
the btrfld ultra low profile (ulp) from above
the handwired and pcb version of the choc btrfld
the btrfld ultra low profile (ulp) from above, folded
the handwired and pcb version of the choc btrfld, folded up
the btrfld ultra low profile (ulp) next to the btrfld pcb aka choc (its 7mm thinner!)
the handwired and pcb version of the choc btrfld with its sibling, the btrfly
5 key dactyl-manuform-mini thumb cluster
flat, tented qwerty keys
6 extra mappable keys
bluetooth (optional)
folds flat for portability
btrfld
btrfld ulp
15.5mm thick (btrfld ulp)
22.5mm thick (btrfld)
btrfld_pcbPCBs
USB C breakout basic breakout board
For most usages, you can just connect VBUS to your 5V input, GND to ground, and D+ and D- as you expect. You can monitor the CC and SBU pins to determine cable polarity, or send side-band data. Or leave them disconnected
A USB 2.0 USB C cable to cut up
46 choc v1 keyswitches, keycaps OR 46 Cherry MX ULP switches
ulp_keycap and ulp_keycap_homenub directories. You need a reasonably high resolution SLA printer to get functional keycaps, FDM won't work.1N4148W SOD-323F diodes
3mm diameter steel rod
1.27mm flat ribbon cable
1x nicenano OR bluemicro840
3d printed pieces, located in the STLs folder
Supports on buildplate
Detect Bridging
100% infill
0.20mm
PLA/PETG
this process is much less tedious than hand wiring. But its still annoying in places since we are trying to keep things thin.
btrfld (non-ulp)
btrfld ulp
stripping ribbon cable:
use cut off diode/resistor legs to connect the controller to the center pcb
the pcbs are designed to hold the diodes "upside down" to keep things as thin as possible. Soldering these is a little hard since they like to stick to the soldering iron.
The UnderbodyWireGuides get super glued into the holes of the pcb. See pictures of the hand underside for details.
Once you have tested the board, use some superglue to reinforce the ribbon cable solder joints
Reference the images in the "BuildPictures/PCB" folder
Prebuilt firmware available in the Firmware directory
Bridge ground + reset twice quickly to put the bluemicro840 into flashing mode
Or press the "bootloader" key on the keyboard if you have already flashed the firmware before
then copy the firmware onto the keyboard
cp build/zephyr/zmk.uf2 /media/<user>/NRF52BOOT/CURRENT.UF2
This is broken until https://github.com/zmkfirmware/zmk/pull/1499 merges, do a local build instead fork this repo, modify the files to your hearts content the github actions workflow will then build it for you https://github.com/SolidHal/zmk-config-btrfld
Grab my fork of the zmk firmware
git clone https://github.com/SolidHal/zmk.git
follow https://zmk.dev/docs/development/setup then
cd zmk
cd app
west build -b bluemicro840_v1 -- -DSHIELD=btrfld
make pristine
west build -p -b bluemicro840_v1 -- -DSHIELD=btrfld
Edit test_fit.FCStd using FreeCad, I used version 0.19-24366
I am by no means a FreeCad expert, so I'm sure it is built suboptimally.
The pcbs were created in kicad
Wiring the underside of the right/left body halves is very tedious
Reference the images in "BuildPictures" and "FinishedPictures" for hints on how to layout the wires
Reference WiringGuide.png to see see the row/colomn layout
Must trim a very very slight amount off of the center pin on keyswitches over the body/thumbcluster rod
Body/ThumbCluster Pivot Rob
Area around the body/baseplate hinge needs clearence, so keep all wires to the other side of the keyswitch
Reference the images in the "BuildPictures" folder
9 wires 420mm
6 wires 240mm 70mm threaded through on the thumb side
Animation: BaseBodyAngle goes from 0 -> 32
firmware: https://zmk.dev/docs/development/new-shield https://zmk.dev/docs/development/setup/ https://zmk.dev/docs/troubleshooting https://github.com/SolidHal/zmk
Friction fit redesign notes: https://markforged.com/resources/blog/joinery-onyx https://www.hubs.com/knowledge-base/how-design-snap-fit-joints-3d-printing/
Cherry MX ULP references: https://github.com/pashutk/Cherry_MX_ULP
No comments yet. Be the first to ask about this board.