BrowseBoardRepo

teensymower-pcbs

Public

@starsurfer78

Download board files

Files for version 1. Pick what you came for.

KiCad projectAll 3,272 files, ready to open in KiCad6.7 MB
For fabricationGerbers, drill, pick-and-place and BOMGerbers and drill zip333 KBGerbers and drill zip: Ardumower282 KBGerbers and drill zip: charge_pcb157 KBGerbers and drill zip: charge_pcb269 KBGerbers and drill zip: charge_pcb196 KBGerbers and drill zip: sender_V1.00148 KBGerbers and drill zip: sender_V1.01148 KBGerbers and drill zip: Teensy_MainPCB.kicad_pcb_backup248 KBGerbers and drill zip: TeensyPCB364 KBPick and place (CSV)5.3 KBPick and place (CSV): Ardumower6.1 KBPick and place (CSV): charge_pcb3.5 KBPick and place (CSV): charge_pcb3.6 KBPick and place (CSV): charge_pcb3.1 KBPick and place (CSV): sender_V1.001.8 KBPick and place (CSV): sender_V1.011.8 KBPick and place (CSV): Teensy_MainPCB.kicad_pcb_backup5.3 KBPick and place (CSV): TeensyPCB6.1 KBBOM CSV29 KB
Schematic PDFEvery sheet, to read or print209 KB
3D modelThe board with its parts, for an enclosure (GLB)3D model (GLB)11 MB3D model (GLB): charge_pcb5.3 MB3D model (GLB): charge_pcb4.7 MB3D model (GLB): charge_pcb6.4 MB3D model (GLB): sender_V1.003.1 MB3D model (GLB): sender_V1.013.1 MB3D model (GLB): TeensyPCB13 MB
Browse all files

Share teensymower-pcbs

Check access before sharing the link.

Who can open this board

Anyone can open this board. No sign-in is required.

https://boardrepo.com/starsurfer78/teensymower-pcbs

This link opens the latest version. Copying it does not grant additional access.

Loading 3D model… large boards can take a moment.

README

DIY Robot Lawn Mower Community: https://www.diy-robot-lawn-mower.com/

Teensymower PCB's - DIY Robot Lawn Mower (Teensy 4.1)

The PCB's are designed to get you started on your own robotic lawnmower project. It doesn't matter if you want to convert a commercial mower or use a 3D printed housing.

The TeensyMainPCB is the brain of the mower to which all sensors and motors are connected. The PowerPCB is responsible for the power supply and monitoring of the battery and the motors. The Wifi SenderPCB is responsible for the perimeter cable and goes into the charging station of the mower.

For your DIY project you need all 3 Boards.

RTK GPS is not yet possible at the moment

Only a few Electronic Parts are needed.

  • JST-XH Connectors
  • Screw Terminal 5.04mm
  • Resistors
  • Pin Header Connector 2.54mm
  • Active Buzzer
  • LED
  • Jumper
  • Teensy 4.1
  • ESP32 DEV Kit V1

Attention: The PCB's are still under development. If you want to order your own PCBs, please check the forum first to see if there are any problems. Use the PCBs at your own risk, no liability is assumed.

)

Robomow RL2000:

Tianchen TC-G158:

Comments

No comments yet. Be the first to ask about this board.

Ask about this board

Sign in to BoardRepo

New here? Signing in creates your account; there is no separate sign-up.