lightboxnano
Publictimgremalm/lightboxnano
Loading…
Imported from GitHub: TimGremalm/LightBoxNano · commit cd6c817 · license GPL-3.0
Description
a generic PCB for controlling LED's both LED strip and WS2812
README
LightBoxNano
a generic LED controller that can be populated for either RGBW LED strip or addressable LED strip like WS2812.
It has the option for populating a pair of potentiometer, and a 5 way slider switch for controlling light modes.
An Arduino Nano is mounted using ordinary 2.54mm pitch pin headers. Optionally a ESP32 Pico Kit can be mounted instead of the Nano, this is much more expensive it is a more powerful MCU and have WiFi.
A RS485 receiver and a pair of XLR connectors can also transform the LED controller into a DMX driver.
Power Supply and voltage rails
Input rail
The input voltage to LightBoxNano are called VIN and can range from 5 to 30V. Make sure to only feed LightBoxNano with a voltage that the LED strip can handle. The maximum voltage is limited by the maximum voltage of the IRLML6344 Mosfets and of what the LED strip can handle.
If using 5V on Vin you need to read "Logic rail" to populate it correctly.
RGBW rail
The positive rail for the LED strip driver is directly fed from VIN, it's usually 12V.
Addressable rail
The positive rail for the addressable LED strip driver is directly fed from VIN, it's usually 5V.
Logic rail
The logic rail should be 5V and feed the micro controller.
There is 2 options for the logic rail:
- Use buck, when Vin is greater than 5.5V.
- Use direct jumper link when Vin is 5V.
Note that the logic rail bypasses Vin_fused.
The buck converter using TI's guide: https://webench.ti.com/power-designer/switching-regulator/select
https://webench.ti.com/appinfo/webench/scripts/SDP.cgi?ID=572687AF787DDED1
Protection circuit
There is 2 options for input protection:
- A classic fuse
- Highside High Current Power Switch
Classic Fuse
A much cheaper option then the high side switch, but one time use only. Populate with a appropriate 1206 fast blow fuse. Example: Fuse Fast Blow 10A 1206 MCCFB1206TFF/10
No reverse polarity protection exist when using a classic fuse.
Highside High Current Power Switch
The Infineon BTS50055-1TMC is a highside high current power switch with buildt in reverse polarity and temperature protection.
It's also used to measure current consumption; Current_Feedback as analog output. To enable the high power switch Enable_Vin_fused must be driven low.
Both Current_Feedback and Enable_Vin_fused goes to the MCU so it can act on over current and act as a resettable fuse.
Vin_fused
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| Current_Feedback | A0 (PC0) | IO38 |
| Enable_Vin_fused | D13 (PB5) | IO37 |
RGBW driver
This is made for LED strip that have red, green, blue and white channels that have a common positive rail like +12V. The LED driver can drive 4 output channels in constant voltage mode at 5A each. The channel can drive up to 10A current if an optional IRLML6344 is mounted. One color channel on a 5m LED strip consisting of 300 LED's will draw 6A (20mA x 300px) when fully lit. A full RGB strip 18A, and a RGBW strip 24A.
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| Red | D5 (PD5) | IO26 |
| Green | D6 (PD6) | IO27 |
| Blue | D9 (PB1) | IO13 |
| White | D10 (PB2) | IO15 |
Addressable LED driver
Addressable LED strip is hooked up directly to VIN and the data pin is going to micro controller via a 1k resistor.
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| Addressable | D3 (PD3) | IO25 |
Control interface
Two potentiometers can optionally be mounted. They are pulled up to 3.3V, so you won't get the full range on the Nano.
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| POT_1 | A1 (PC1) | IO26 |
| POT_2 | A2 (PC2) | IO27 |
A 10 position rotary coded switch can optionally be mounted for selecting different modes.
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| SwCode1 | D7 (PD7) | IO14 |
| SwCode2 | D8 (PB0) | IO12 |
| SwCode4 | D11 (PB3) | IO2 |
| SwCode8 | D12 (PB4) | IO4 |
10 position switch is coded in binary.
| Code | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | * | * | * | * | * | |||||
| 2 | * | * | * | * | ||||||
| 4 | * | * | * | * | ||||||
| 8 | * | * |
Also a pin header of the Arduino Nano will be easily assessable for hooking up random stuff.
DMX Tranceiver
A RS-485 transceiver can optionally be mounted for sending and receiveing DMX512. It uses ADM2687E which isolates the RS-485 bus from the low voltage micro controller side. This is important as electrical errors down the bus can propagage along the bus. ADM2687E also isolates the power on the bus side by a buildt in DC to DC converter.
The tranceiver can be set to send DMX data if the jumper links "Link_DriverOutputA1" and "Link_DriverOutputB1" is soldered.
| Jumper | Description |
|---|---|
| Link_DriverOutputA1 | Links the Z (Driver Inverting Output) to DMX+ |
| Link_DriverOutputB1 | Links the Y (Driver Noninverting Output) to DMX- |
| Receiver_Disable1 | Pulls RE (Receiver Enable) to High which disables receiver |
| Receiver_Enable1 | Pulls RE (Receiver Enable) to Low which enables receiver |
| Driver_Enable1 | Pulls DE (Driver Enable) to High which enables sender |
| Driver_Disable1 | Pulls DE (Driver Enable) to Low which disables sender |
| Link_TransceiverGnd_To_DMXgnd1 | Links DMX bus Gnd to ADM2687E Gnd2 |
| Link_DMXgnd_To_DMXchassignd1 | Links DMX ground shield to ADM2687E Gnd2 |
DMX Send and Receive can be hooked up to UART channels on a MCU. Receiver Enable and Driver Enable can also be driven by the micro controller (only ESP32).
| Channel | Arduino Nano | ESP32 |
|---|---|---|
| DMX_Send | D1 TX (PD0) | IO21 |
| DMX_Receive | D0 RX (PD1) | IO22 |
| DMX_ReceiveEnable | N.C | IO19 |
| DMX_DriveEnable | N.C | IO23 |
MCU
An Arduino Nano V3 (ATmega328) is selected because it's cheap, available and have enough power for most applications.
Another option is to mount a ESP32 Pico Kit instead which is much more powerful and have built in WiFi.
No comments yet. Be the first to ask about this board.