Loading 3D model… large boards can take a moment.
This is a daughterboard that allows to have dual SID audio in a C128DCR. Although C128DCR has a huge case the space near SID and MMU is very awkward due to power supply.
This project is meant for two 8580 chips, as far as I know the only type installed in C128DCRs. But you never know, so just in case I left information about supporting 6581 SIDs too.
The goal of this project was to make the PCB fit in the narrow area between power supply and already installed 256K MMU expansion.
The audio output is mixed as 6-voices mono and passed through onboard amplifier to audio/video port.
The board supports various modes for external input, including noise reduction and digi boost.
This is basically a fusion of ideas from two projects:
I have mostly done measurements and shaped the PCB.
PDF plot of the schematic can be found here.
kicad folder contains all the KiCad 6.0 project files for C128DCR.
kicad-c128d folder contains all the KiCad 6.0 project files for C128D.
kicad/plots folder contains Gerber files for manufacturing a PCB.
The PCB hugs 256K MMU expansion board on one side, tries to avoid power supply on the other side and also has to leave space for screw standoff under the power supply module.
kicad-c128d/plots folder contains all the KiCad 6.0 project files for C128D.
Both SID chips must be identical. For C128DCR these should be usually MOS 8580 powered by 9V.
For 8580:
For 6581:
Jumpers JP1/JP3 (SID#1) and JP2/JP4 (SID#2) control external input/noise reduction/digi boost signal routing.
JP1 and JP2 (square pad is pin 1):
JP3 and JP4 (square pad is pin 1):
You can also keep all jumpers open to make external input floating. Some people claim that it's another way of reducing the noise.
For digi boost additionally set RV1 and RV2 trimmers while playing some sampled audio to bring digital sound to an acceptable volume level relative to regular SID voices.
MixSID configuration tool has excellent description of both noise reduction and digi boost modes.
On the image above there is a single ARMSID as primary SID and an unpopulated socket for secondary SID.
For both chips the board is configured with JP3/JP4 for digi boost, so JP1/JP2 set to noise reduction are irrelevant.
Note that R8 is installed here by mistake, but its one leg was cut.
SID_ADAPTER footprint first.There are small holes in the PCB where plastic standoffs can be put to support the board on both ends and reduce stress on the mainboard SID socket. It's especially important on the top right end, next to secondary SID.
After assembling two such boards I noticed that power supply modules in different C128DCRs have different dimensions. To be sure that nothing will be shorted I put kapton tape on the whole left-hand side of the board after installation, also covering socketed primary SID.
Start by soldering round pins to row closest to the PCB's edge and to the row marked on the silkscreen. Then proceed with C128DCR instructions.
You need to decide where in the I/O memory space SID#2 will be available. Even though signal for $D700 is easily available on C128 (it's pin 12 of U3) most stereo/dual SID tunes use $D420, $D500 or $DE00.
For quick tests SID#2 chip select signal (/CS2_IN, the square pad on J4 connector) can come from I/O1 signal to make SID#2 appear at $DE00 address.
You don't need to reach to expansion port for that, it's already available on pin 9 of U3. Obviously it's not compatible with cartridges but allows for a quick test.
Download this tune: https://csdb.dk/release/?id=96893 and run. Hit '3' to choose $DE00 and you should hear the music - it starts immediately playing on SID#2 channels, SID#1 joins later - after about 30s.
Check out my other project for a better solution to make SID#2 appear at $D420, $D500 (in C64 mode) and optionally at $DE00.
No comments yet. Be the first to ask about this board.