Loading files…
goya1746 is an overdrive & preamp pedal based on the legendary Diezel VH4 channel 3. Fully open circuit board designed in KiCad 8. The main idea was to avoid oscillations on all gain levels. This project is shared for hobbyists who want to study, modify, or build their own. The full PCB outline is 115 × 70 mm (4.53 × 2.76 in), but the usable area is about 96 × 70 mm (3.78 × 2.76 in) if you remove the side "wings" in KiCad and define your own edge cut before generating Gerbers. In theory, it should fit a 1590BB enclosure, but keep in mind that each potentiometer is wired separately and the connection pads are not located at the corners of the PCB, so there will be quite a lot of wiring inside.
Check Releases page for .zip Gerber files ready for production.
If you want to fabricate the PCB, just upload the .zip Gerber files to your favorite board house (e.g. JLCPCB, PCBWay, NEXTPCB). Make sure you can source all components in the correct form factor before manufacturing the board.
P.S. Future releases are not expected in the near term due to financial constraints. However, once the situation improves, development will continue, including projects such as Turbo Rat, SansAmp GT-2, Boss CE-2, as well as a search for the best fuzz circuit.
These guides might help beginners who have never built their own pedals. Some links might become broken.
All resistors are 1/4 W metal film with 1% tolerance. All capacitors must have a minimum voltage rating of 35 V. Consider capacitors to be polypropylene film unless otherwise specified. If 25 kΩ potentiometers are unavailable, a 50 kΩ potentiometer may be used together with a 50 kΩ resistor in parallel. This changes the taper slightly (especially for log pots), because the resistance curve is altered by the parallel resistor. Ferrite bead R1 is optional and can be replaced with a wire link. The OPA2134 at U1 may be substituted with another TL072 without any noticeable difference.
You'll also need:
This pedal provides two output options: Guitar Out and Power Out. In most cases, you won't need to wire both. If the pedal is used at the end of a signal chain (similar to a real amplifier), Power Out is the preferred choice. Power Out is a low-impedance, line-level signal, so it can be safely connected to standard line inputs, such as those on audio interface. Guitar Out is a traditional high-impedance output suitable for connecting to other pedals or amp inputs.
For ICs and other essential components, use reputable suppliers only. Avoid sources like eBay or AliExpress, as counterfeit or unreliable parts are widespread on those platforms and may cause malfunction or failure.
| Reference | Value | Qty | Notes |
|---|---|---|---|
| BASS1 | A1M | 1 | |
| C1,C7,C15,C16 | 22n | 4 | |
| C2,C6,C13 | 100p | 3 | Ceramic Disc |
| C3,C4,C5,C17 | 1u | 4 | |
| C8 | 2n2 | 1 | |
| C23 | 2n2 | 1 | Ceramic Disc or Film |
| C9,C12,C18 | 2u2 | 3 | |
| C10 | 47p | 1 | Ceramic Disc |
| C11 | 4n7 | 1 | |
| C14 | 560p | 1 | Ceramic Disc |
| C19 | 330n | 1 | |
| C20,C22 | 10u | 2 | |
| C21 | 1n | 1 | Ceramic Disc or Film |
| C24,C25,C26,C27,C28 | 47u | 5 | Electrolytic ~35V |
| D1,D2,D5,D6 | 1N4148 | 4 | Signal diode, DO-35 |
| D3,D4 | 1N4734A | 2 | 5.6V zener (equivalents: 1N752, 1N5232), DO-41 |
| D7 | LED 12V | 1 | Require ~2.2K resistor |
| J1 | GUITAR INPUT | 1 | |
| J2 | DC INPUT | 1 | |
| J3 | POWER OUT | 1 | |
| J4 | GUITAR OUT | 1 | |
| R1 | FerriteBead | 1 | Optional |
| R2,R3,R14 | 1M | 3 | |
| R4,R5,R15,R25,R37 | 100K | 5 | |
| R6,R13,R18,R33 | 10K | 4 | |
| R7,R10,R11,R17,R19 | 220K | 5 | |
| R8,R16 | 470K | 2 | |
| R9 | 680K | 1 | |
| R20 | 39K | 1 | |
| R24 | 1M5 | 1 | |
| R26,R34 | 1K | 2 | |
| R28 | 100R | 1 | |
| R30 | 47R | 1 | |
| R31 | 56K | 1 | |
| R32 | 4K7 | 1 | |
| R36 | 150K | 1 | |
| R38,R39 | 10R | 2 | |
| U1 | OPA2134 | 1 | Dual op-amp, DIP8. May be substituted with TL072 |
| U2,U3 | TL072 | 2 | Dual op-amp, DIP8 |
| IC4 | LM2940CT-12_NOPB | 1 | Low-dropout voltage regulator +12V |
| IC100 | TC1044SCPA | 1 | Charge Pump IC, DIP8 |
| DEEP1,PRES1 | C25K | 2 | |
| GAIN1 | A250K | 1 | |
| MID1 | B25K | 1 | |
| TREBLE1 | B250K | 1 | |
| VOL1 | A10K | 1 |
The chassis should be properly grounded to ensure effective shielding and noise reduction. Where possible, use cables with an outer braided shield and connect the shield to ground at least on one end — preferably at the PCB side. The metal backs of potentiometers may also be connected to ground to help reduce noise pickup through their housings. Ground loops are generally not a concern inside a small enclosure such as a pedal, so a strict star-ground topology is unnecessary. The DC input jack must be plastic (isolated from the enclosure). Most pedals use a negative center power supply, so a metal jack touching the chassis could short the positive voltage to ground.
As a side note. There are a lot of myths and misconceptions about grounding in PCB design, mostly because of the many variables that need to be considered together with each statement. At some point, you think you understand how it works, but then you realize you don't. It's not always clear what the real cause of a problem is, and fixing one issue can accidentally fix another, leading to false conclusions.
For example, advanced grounding techniques are mainly used for high-frequency applications, and the effects are often negligible in the audio range (up to 20 kHz). Through-hole components are considered obsolete for high-frequency PCBs, yet they are abundant in most analog music equipment. If we start replacing everything with SMD components, we might lose some of the unique characteristics that contribute to the sound we expect, or just our own perception might change.
And let's not forget that the sound we're looking for doesn't always have to be perfect — it just has to be pleasant to our ears. Who wants to listen to a perfectly clean sine wave, right? We enjoy it when it's mixed with other harmonics and subtle modulations that make the sound feel alive. Often, it's exactly those imperfections in the components and PCB layout that create the desired effect.
This hardware design is distributed under the MIT License. Copyright (c) 2025 Dmitry Escaroda.
If you build this pedal, feel free to share photos or mods via Discussions. If you are an experienced Electronics Engineer or PCB Designer and see how something could be improved for the benefit of all, please submit an issue.
No comments yet. Be the first to ask about this board.