Loading files…
An open platform for turning cheap servos into smart actuators.
OpenServoCore (OSC) is open hardware and firmware that drops a CH32V006 control board into a $2-3 cloned hobby servo (SG90 and friends) and turns it into a DXL-style smart actuator — position feedback, current sensing, bus-addressable, programmable.
The thesis is the price point: at mass-production volume, an OSC swap board should add no more than ~$1 to the BOM of a cloned servo. Cheap enough that "upgrade every servo in a robot to smart" stops being a premium decision and starts being a default.
In active development. Nothing here is shippable yet. The firmware is being rewritten, the dev board is validated and integrating with firmware, and the swap board is designed but not spun.
osc-dev-v006) — Rev B validated. Firmware integration ongoing.sg90-prod-ch32v006) — designed, not spun. Waiting on firmware v2 to be testable against.firmware-old/) — legacy. First pass was vibe-coded and got poor Reddit feedback. Kept as historical reference; not a target for new work.OpenServoCore/tinyboot.open-servo-core/
├── hardware/
│ ├── boards/
│ │ ├── osc-dev-v006/ # OSC Dev CH32 — has its own README with pinouts, jumpers, bringup notes
│ │ ├── sg90-prod-ch32v006/ # OSC SG90 CH32 swap board (designed, not spun)
│ │ ├── servo-dev-board-stm32f301/# Retired hobby-phase STM32 dev board (legacy)
│ │ ├── encoder-board/ # Optional quadrature encoder breakout for J8 experiments
│ │ └── motor-mount/ # 3D-printable test fixtures
│ ├── shared.kicad_sym / shared.pretty / shared.3dshapes # Shared KiCad libraries
│ └── templates/ # KiCad project templates
├── firmware/ # Firmware v2 lives here once the rewrite starts
└── firmware-old/ # Legacy firmware (do not use)
The OSC bootloader, tinyboot, is a separate repo. It's part of the OSC firmware stack but versioned and released independently — its chip-support matrix (V003 / V00x / V103) is broader than the OSC boards on purpose.
OSC boards follow OSC <Form> <ChipFamily>:
osc-dev-v006.sg90-prod-ch32v006.Engineering SKUs (osc-<form>-<chip>-rev-<letter>) appear in BOMs and schematic title blocks; the names above are what you'll see in posts and docs.
OSC standardizes on the CH32V006 — 48 MHz RISC-V, 62 KB flash, 8 KB RAM. Chosen because it's the chip that makes the ≤$1 BOM uplift work. No multi-chip roadmap; one chip, done well.
Each board has its own README with full schematics, pinouts, jumper behaviour, and bringup notes:
The Rust firmware is mid-rewrite. The legacy firmware-old/ tree contains the original architecture (multi-crate workspace targeting STM32F301 and partly CH32V003) and is kept for reference, but the v2 rewrite starts from a cleaner architecture targeting CH32V006 first. Plan: DXL-compatible register table, persistence, control loops, safety features.
Build instructions will appear here as the rewrite matures.
This is early — the most useful thing right now is following along and asking questions, not opening PRs.
Dev boards are fabricated and assembled by PCBWay — sponsor since Feb 2026.
Five PCBA boards delivered. Build and assembly quality clean across all five — no fabrication issues. Bring-up turned up design issues on my side (VDD/VSS swap, silkscreen errors), but those traced back to my own schematic, not the manufacturing. The process itself was painless. A late BOM swap (RS1 shunt 100 mΩ → 10 mΩ) was accepted without fuss; the pre-fab assembly review caught a pad-clearance concern before manufacturing.
Full spin + bring-up writeup: CH32V006 dev board first spin.
Five PCBA boards delivered, May 2026. Validated. PCBWay's pre-fab manufacturability review flagged nothing, and build/assembly quality was again clean. A small bug found in the sponsored boards (shared nRST / OPN2 pin) didn't warrant another validation round — patched in-rev with a solder bridge. The published files include the patch.
Reference design available as a PCBWay community project for one-click ordering.
OSC is fully open. No dual licensing, no commercial gates.
No comments yet. Be the first to ask about this board.