Loading files…
IOTTeach v1.0 — Top side (above) · Bottom side (below)
| Section | Description |
|---|---|
| About | Overview and intent |
| Hardware Overview | Technical summary |
| Key Features | Highlights and educational notes |
| Block Diagram | System block diagram |
| Getting Started | Quick start and assembly checklist |
| Lab Scenarios | Suggested exercises by level |
| License | License guidance |
IOTTeach is a detachable plug-in kit designed for hands-on learning, quick hardware validation, and classroom labs. It exposes common peripherals (relays, RGB/status LEDs, buzzer) and standard 2.54 mm headers for power, analog, and digital lines so students and developers can prototype with any MCU or SBC without soldering a custom shield.
Design philosophy: Bring Your Own MCU — connect any microcontroller (ESP32, STM32, Arduino, Raspberry Pi Pico, etc.) using Dupont wires.
| Component | Detail |
|---|---|
| Power | DC jack (DC-005) + terminal block → TPS54202 buck converter → 3.3V/5V rail |
| GPIO Headers | Digital 1×10 · Digital 1×8 · Analog 1×6 · Power header (pitch 2.54 mm) |
| LED Indicators | 2× WS2812B RGB, discrete status LEDs (green/yellow/red) |
| Audio | Piezo buzzer (CMT-8530S-SMT), PWM capable |
| Relays | 2× Omron G5NB SPST relays, driven via SS8050 transistors |
| Protection | SS34 Schottky diodes for flyback, decoupling capacitors and input protection |
| Project Files | KiCad project and production outputs under hardware/IOT1_V1.0/production/ |
• TPS54202DDC — Buck converter (3.3V, up to ~2A)
• WS2812B (×2) — Addressable RGB LEDs for visual feedback
• Omron G5NB Relays (×2) — SPST relays for switching experiments (observe safety limits)
• CMT-8530S-SMT — Piezo buzzer for audible signals
• SS8050 (×3) — NPN transistors as relay drivers
• SS34 (×4) — Schottky diodes for flyback/protection
hardware/IOT1_V1.0/production/ for easy handoff to PCB fabs and assemblers. ┌─────────────────────────────────────┐
│ IOTTeach Board │
└─────────────────────────────────────┘
│
┌───────────────────────────────────────────────────────────────────┐
│ │
▼ ▼
┌───────────────┐ ┌───────────────┐
│ POWER INPUT │ │ MCU SIDE │
│───────────────│ │───────────────│
│ • DC Jack │ │ • Digital I/O │
│ • Terminal │──► TPS54202 ──► 3.3V/5V Rail ──► │ • Analog In │
│ Block │ Buck │ • Power │
└───────────────┘ └───────┬───────┘
│
┌───────────────────────────────────────────────────────────────┘
│
▼
┌─────────────────────────────────────────────────────────────────────────────┐
│ PERIPHERALS │
├─────────────────┬─────────────────┬─────────────────┬───────────────────────┤
│ VISUAL │ AUDIO │ ACTUATORS │ INPUTS │
├─────────────────┼─────────────────┼─────────────────┼───────────────────────┤
│ • 2× WS2812B │ • Piezo Buzzer │ • 2× SPST Relay │ • 2× Tactile Switch │
│ • Status LEDs │ (PWM tone) │ (5A/250VAC) │ │
│ │ │ • SS34 Flyback │ │
└─────────────────┴─────────────────┴─────────────────┴───────────────────────┘
# Clone repository
git clone https://github.com/SonDinh23/IOTTeach.git
cd IOTTeach
# Open the KiCad project:
# File → Open Project → hardware/IOT1_V1.0/IOT1_V1.0.kicad_pro
This project is presented as Open Hardware. Please add a specific license (for example, CERN-OHL, TAPR-OHL, or CC-BY-SA) to the repository before distributing manufacturing files or derivative works.
Thank you for exploring IOTTeach. Contributions, documentation improvements, and lab material suggestions are welcome — open an issue or submit a pull request.
| Tính năng | Mô tả |
|---|---|
| MCU Agnostic | Tương thích ESP32, STM32, Arduino, Raspberry Pi Pico, v.v. |
| Plug & Play | Kết nối nhanh qua dây Dupont, không cần hàn |
| Header chuẩn | Pitch 2.54mm phổ biến, dễ tìm phụ kiện |
| Tính năng | Mô tả |
|---|---|
| Clear Layout | Component spacing rộng, dễ đo đạc oscilloscope |
| Labeled Headers | Đánh dấu rõ ràng chức năng từng chân |
| Gradual Learning | Từ LED → Switch → Buzzer → Relay → RGB |
| Tài liệu | Đường dẫn |
|---|---|
| Schematic | hardware/IOT1_V1.0/IOT1_V1.0.kicad_sch |
| PCB Layout | hardware/IOT1_V1.0/IOT1_V1.0.kicad_pcb |
| 3D Model | hardware/IOT1_V1.0/IOT1_V1.0.step |
| BOM | hardware/IOT1_V1.0/production/bom.csv |
| Pick & Place | hardware/IOT1_V1.0/production/positions.csv |
┌─────────────────────────────────────┐
│ IOTTeach Board │
└─────────────────────────────────────┘
│
┌───────────────────────────────────────────────────────────────────┐
│ │
▼ ▼
┌───────────────┐ ┌───────────────┐
│ POWER INPUT │ │ MCU SIDE │
│───────────────│ │───────────────│
│ • DC Jack │ │ • Digital I/O │
│ • Terminal │──► TPS54202 ──► 3.3V/5V Rail ──► │ • Analog In │
│ Block │ Buck │ • Power │
└───────────────┘ └───────┬───────┘
│
┌───────────────────────────────────────────────────────────────┘
│
▼
┌─────────────────────────────────────────────────────────────────────────────┐
│ PERIPHERALS │
├─────────────────┬─────────────────┬─────────────────┬───────────────────────┤
│ 💡 VISUAL │ 🔊 AUDIO │ ⚙️ ACTUATOR │ 🎛️ INPUT │
├─────────────────┼─────────────────┼─────────────────┼───────────────────────┤
│ • 2× WS2812B │ • Piezo Buzzer │ • 2× SPST Relay │ • 2× Tactile Switch │
│ • 2× LED Green │ (PWM tone) │ (5A/250VAC) │ │
│ • 1× LED Yellow │ │ • SS34 Flyback │ │
│ • 3× LED Red │ │ │ │
└─────────────────┴─────────────────┴─────────────────┴───────────────────────┘
# 1. Clone repository
git clone https://github.com/SonDinh23/IOTTeach.git
cd IOTTeach
# 2. Mở project KiCad
# File → Open Project → hardware/IOT1_V1.0/IOT1_V1.0.kicad_pro
| Bước | Thành phần | Ghi chú |
|---|---|---|
| 1️⃣ | Power Stage | TPS54202, inductor L1, capacitors, SS34 diodes |
| 2️⃣ | Headers | Tất cả pin headers (J1-J14) |
| 3️⃣ | Passives | Resistors, capacitors còn lại |
| 4️⃣ | Semiconductors | Transistors SS8050, LEDs |
| 5️⃣ | Modules | Relays, buzzer, WS2812B |
| 6️⃣ | Connectors | DC jack, terminal blocks, switches |
| Bài lab | Mô tả | Kỹ năng |
|---|---|---|
| LED Blink | Điều khiển LED đơn ON/OFF | Digital Output |
| Button Read | Đọc trạng thái nút nhấn | Digital Input, Pull-up |
| Buzzer Tone | Tạo âm thanh với tần số khác nhau | PWM basics |
| Bài lab | Mô tả | Kỹ năng |
|---|---|---|
| RGB Rainbow | Hiệu ứng cầu vồng với WS2812B | NeoPixel protocol |
| Relay Timer | Bật/tắt relay theo thời gian | Timing, State machine |
| Multi-LED Pattern | Đèn chạy đuổi, hiệu ứng | Arrays, Loops |
| Bài lab | Mô tả | Kỹ năng |
|---|---|---|
| Smart Alarm | Hệ thống báo động: buzzer + LED + relay | System integration |
| Power Profiling | Đo dòng tiêu thụ ở các chế độ | Instrumentation |
| IoT Control | Điều khiển relay qua WiFi/BLE | Networking |
Dự án này được phát hành dưới dạng Open Hardware.
⚠️ Vui lòng thêm license cụ thể (CERN-OHL, TAPR-OHL, hoặc CC-BY-SA) trước khi phân phối thiết kế.
Cảm ơn bạn đã quan tâm đến IOTTeach!
Mọi góp ý về thiết kế, tài liệu hướng dẫn, hoặc ý tưởng bài thực hành đều được hoan nghênh.
No comments yet. Be the first to ask about this board.