KiCad and hardware projects using IC
Open IC hardware projects on BoardRepo, the GitHub for hardware. View the schematic, PCB, and BOM in your browser and download the KiCad sources, BOM, and Gerbers.
Projects
I made my 4 layers board wearble with microphone, ESP32 S3. Everything works but bluetooth is broken, can anyone tell my whyyyy
This board is a Bluetooth to PC audio bridge! It lets you connect devices such as consoles or phones to it via Bluetooth to transmit audio, and then the board sends the audio through to your PC headphones with a wired connection!! TLDR: It lets you pass audio through to your PC from external devices :D
BelayBox reference hardware
Karabas-Go PCB
Project Caribou documentation, designs, and project artifacts.
YKTSAT Kicad board files - mirror of https://git.yktaero.space/yktaero-dev/cubesat-boards
rp2040 pro micro drop in
Real-time Wearable-based Cardiac Monitoring with Machine Learning
Repository for the PCB design for the BIRDS-X project
Low-power CO2, temperature and humidity monitor using ESP32-C6 and E-Paper display.
A breakout board of MCP25625 for Can BUS communication.
No description.
A sub-micrometer 3D motion control plattform.
Switch v5 Hardware (WIP)
multi-ASIC Bitcoin miner
CAD and code for the Playdate Cabinet
Wall mounted 4 inch touch display panel with CM4 inside
Contactless Battery Solution for Sustainable IoT Devices: Assessment of Environmental Impact
A wireless ergonomic keyboard
Aries, an OpenHPSDR ATU (kicad version)
Cheap logic probe for Rigol MSO5000-series oscilloscopes
A new version of my project to create a fully custom GPS receiver
The 2025 Hackaday Supercon RF Communicator Badge
A minimalist 1W LoRA PCB design for Meshtastic-device firmware
Anotter USB temperature logger that can record up to four channels with thermocouple or NTCs connected via CDC directly or SCPI to USB.
The Open Book: Project Reboot
MUUU!: Livestock Smart Collar 🐮
Open Source 8-channel EEG Pi Pico Shield for <$80
An IOT device built of the raspberry pi
<<<<<<< HEAD NewSky📺 中文版本
The source for the environmental sensors used at Kwartzlab
PART (Purdue Aerial Robotics Team) PDU (power distribution unit) and Pixhawk Carrier KiCad projects and accompanying embedded code
Want to send measurements back to a server through HTTP or MQTT? This is about it along with the PCB design, 3D box and support for data storage with maticas API
using ESP32C3 chip to collect and analyze air quality data
ESPHome Indoor Multi-Sensor hardware. This design supports Radar/PIR Presence, Temperature, Humidity, Pressure, Light, CO2, CO, VOC, NOX and PM sensors. Add a speaker and microphone and you have the kitchen sink too! Click the link below to configure a new device.
LibreCellular RF Front-End Hardware Design
IOT BandSelector (also known as a Band Decoder) works with Antenna Switch Controller to perform automated antenna selection on band change
Custom keyboard using the caps from the Alcatel-Lucent MMK, built with Onshape and KiCad
https://hackaday.io/project/181521-freeeeg128-alpha
https://hackaday.io/project/181683-freeeeg32-alpha131
Olin's National Eclipse Ballooning Project team repository
Hardware for OreSat's SDR GPS receive and other SDR GPS projects
Saul Sanchez Abreu 20211867
Code and PCB designs for AutoBloomer MQTT sensor modules
NNA-FPGA-Power-Measurement-System
Bearbeitet von Lukas
A prototype Full Stack fully Open Source NV Center Diamond Magnetometer
A low-power ZigBee sensor integrated with HomeAssistant for monitoring temperature, humidity, and CO2.
Mixed-signal electronics, PCB design, embedded systems, hardware bring-up, and circuit debugging using KiCad/Altium, C++, Python & oscilloscopes.
Reverse engineered Raspberry Pi Compute Module 5
Haptic input knob with software-defined endstops and virtual detents
Silversat Ground Station Radio Board
sp26-cmpe-195a-group-project-CMPE195_Template-1 created by GitHub Classroom
A collection of open source hardware that has been designed by Spaceboards
HW files of COBC
KiCAD Files for all WINTER (Wireless Inertial iNformation and Telemetry for Energetics Regulation) flight computer
Analog keypad with hall effect switches and rapid trigger for osu!
An experimental PC adapter for EPCOT —the PlayStation®VR2 headset— that splits USB Type-C® into DisplayPort video, USB 3 data and power. Intercepting its DP-AUX/SBU and CC side channels.
KiCad-designed Control and Power PCBs for a minesweeper competition robot, featuring an Arduino Mega, motor drivers, IMUs, and an automatic safe-shutdown circuit.
一个可以通过PD诱骗BOOST升压到24V（通过修改反馈电阻可调）输出的工具