Hardware projects tagged multiboard-revert-reimport
Open hardware projects tagged multiboard-revert-reimport on BoardRepo, the GitHub for hardware. View schematics and PCBs in the browser and download the sources.
Projects
BelayBox reference hardware
Karabas-Go PCB
Project Caribou documentation, designs, and project artifacts.
YKTSAT Kicad board files - mirror of https://git.yktaero.space/yktaero-dev/cubesat-boards
rp2040 pro micro drop in
Real-time Wearable-based Cardiac Monitoring with Machine Learning
Repository for the PCB design for the BIRDS-X project
Open-source air quality monitor built around an ESP32 microcontroller, SEN55 module and custom breakout board.
Low-power CO2, temperature and humidity monitor using ESP32-C6 and E-Paper display.
A breakout board of MCP25625 for Can BUS communication.
No description.
A sub-micrometer 3D motion control plattform.
Switch v5 Hardware (WIP)
multi-ASIC Bitcoin miner
Charge your Dualshock 4 using the EXT port with this board.
A replacement board for a Wii U dock, with a USB type C connector.
Custom made keyboard, enchanced with amazing looks and ergonomics!
CAD and code for the Playdate Cabinet
Wall mounted 4 inch touch display panel with CM4 inside
Contactless Battery Solution for Sustainable IoT Devices: Assessment of Environmental Impact
A wireless ergonomic keyboard
Read Me
Aries, an OpenHPSDR ATU (kicad version)
Cheap logic probe for Rigol MSO5000-series oscilloscopes
This is the repository for Raspberry Pi Full Stack Upgrade Project, a course from Tech Explorations.
A new version of my project to create a fully custom GPS receiver
The 2025 Hackaday Supercon RF Communicator Badge
A minimalist 1W LoRA PCB design for Meshtastic-device firmware
Anotter USB temperature logger that can record up to four channels with thermocouple or NTCs connected via CDC directly or SCPI to USB.
The Open Book: Project Reboot
A little module with two TB67H450FNG.
MUUU!: Livestock Smart Collar ๐ฎ
Open Source 8-channel EEG Pi Pico Shield for <$80
An IOT device built of the raspberry pi
<<<<<<< HEAD NewSky๐บ ไธญๆ็ๆฌ
The source for the environmental sensors used at Kwartzlab
PART (Purdue Aerial Robotics Team) PDU (power distribution unit) and Pixhawk Carrier KiCad projects and accompanying embedded code
ESP32 Firmware for controlling a train
Database QuestDB database, set ip & port in config.py on sensor (default works on port 9000)
| Supported Targets | ESP32 | ESP32-C3 | ESP32-C5 | ESP32-C6 | ESP32-H2 | ESP32-P4 | ESP32-S3 | | ----------------- | ----- | -------- | -------- | -------- | -------- | -------- | -------- |
Want to send measurements back to a server through HTTP or MQTT? This is about it along with the PCB design, 3D box and support for data storage with maticas API
using ESP32C3 chip to collect and analyze air quality data
ESPHome Indoor Multi-Sensor hardware. This design supports Radar/PIR Presence, Temperature, Humidity, Pressure, Light, CO2, CO, VOC, NOX and PM sensors. Add a speaker and microphone and you have the kitchen sink too! Click the link below to configure a new device.
LibreCellular RF Front-End Hardware Design
IOT BandSelector (also known as a Band Decoder) works with Antenna Switch Controller to perform automated antenna selection on band change
Custom keyboard using the caps from the Alcatel-Lucent MMK, built with Onshape and KiCad
https://hackaday.io/project/181521-freeeeg128-alpha
https://hackaday.io/project/181683-freeeeg32-alpha131
Olin's National Eclipse Ballooning Project team repository
Hardware for OreSat's SDR GPS receive and other SDR GPS projects
Mechanical keyboard for left hand with Raspberry Pi Pico for games.
Split 36-key keyboard
ESP32-based BLDC motor controller built with ESP-IDF, utilizing Hall sensors and the hardware MCPWM peripheral.
Saul Sanchez Abreu 20211867
Code and PCB designs for AutoBloomer MQTT sensor modules
NNA-FPGA-Power-Measurement-System
Bearbeitet von Lukas
A prototype Full Stack fully Open Source NV Center Diamond Magnetometer
A low-power ZigBee sensor integrated with HomeAssistant for monitoring temperature, humidity, and CO2.
Mixed-signal electronics, PCB design, embedded systems, hardware bring-up, and circuit debugging using KiCad/Altium, C++, Python & oscilloscopes.